triadaoasis.blogg.se - Bitburner wiki

#BITBURNER WIKI INSTALL#
#BITBURNER WIKI MOD#
#BITBURNER WIKI UPDATE#
#BITBURNER WIKI MANUAL#
#BITBURNER WIKI CODE#

Even though Bitburner is set in a dystopian future where you work alone in front of a green tinted monitor, that doesn't mean we can't create a thriving community to help each other out! no needs particular firmware.For inspiration, assistance, and discussion around the amazing cyperpunk-themed incremental RPG, Bitburner. The Avalon2/3 MM firmware support testing out of box.Test 10 avalon2 single module with one host (703N or RPi).Cgminer works fine(the kernel user driver, cgminer it self, cgminer-monitor and uci configurations files).Either and WiFi(703N) connect works fine.have to keep some space for save configuration New firmware don't break Avalon for sure.Fixed fan speed can be change by users.Include an ASIC cores testing python script.Display all modules status include 2 fan, 2 temperature sensors, voltage and frequency.Support fixed fan speed, support A3255 frequency from 1G to 2G, support adjust voltage for 0.65v to 1.1v.MM( 201401-a3cb3950): Include the first stable version of MM firmware.MM( 201401-1f7d08b0): read the power good single back.Support voltage setting for Avalon2 and Avalon3 chips on cgminer configuration page.Support frequency setting for Avalon2 and Avalon3 chips on cgminer configuration page.Add some text for support both Avalon2 and Avalon3.Display GHS(not MHS) on cgminer status page.Detect Avalon power good signal in cgminer.Support 703N, 1043ND-V2 and RaspBerry Pi.Fix a bug that may cause hashrate lose.

#BITBURNER WIKI UPDATE#

Update OpenWrt to r40351 (Linux version 3.10.34).Update CGminer from 4.0.0 to 4.3.0 (You may want read document on -config options).

#BITBURNER WIKI CODE#

Code improvement: dev type detect, job_id crc16 compare, display GHS, etc.

Fixed hashrate count when start and ignore disabled module.

Cut the ASIC power when network was down for 3 minutes.

Fix the share cannot count to correct device(miner thread).

Add option: -avalon2-fixed-speed Set Avalon2 fan to fixed speed.

Add option: -avalon2-cutoff Set Avalon2 overheat cut off temperature (default: 88).

Update to OpenWrt r40859, Update cgminer to 4.3.3.

Display indicator status on status page.

Support unlimited socket receive size for cgminer-api.

Add new parameter for stratum ignore time: -stratum-ignore (Default: 30s).

Add new parameter for polling delay: -avalon2-polling-delay (Default: 20ms).

Ignore blacklisted and zombie devices on luci status page.

Fan speed auto adjust with new method,range support.(cgminer param: -avalon2-fan 50-100 or -avalon2-fan 50).

Support p2pool(with MM Version: 331408-a15cac80).

Merge cgminer to ckolivas's trunk(V4.5.0).

OpenWrt cgminer package, files and config.

LEDS From bottom (FPGA) to top is 1 to 8: Power Module conversion efficiency: >= 87%ĭesign Operating temperature: 85C (chip temperature), 60C (PCB, temperature sensor measurements)įan: 4PIN PWM speed control, report fan speed back. Module Power: 294W (excluding fan power consumption). cgminer -avalon2-freq 500 -avalon2-voltage 7250 -avalon2-fan 50 -o -u work -p pass If you use cgminer 4.5.0, the command will like this: cgminer -S /dev/ttyUSB0 -avalon2-freq 500 -avalon2-voltage 7250 -avalon2-fan 50 -o -u work -p pass Inside your home directory, download Cgminer

#BITBURNER WIKI INSTALL#

Sudo apt-get install openssh-server byobu Sudo apt-get install libcurl4-openssl-dev pkg-config libtool libncurses5-dev libudev-dev screen xterm

Chip Freq: 1700, Voltage: 10750 -> 119GHsĮxtra cooling is recommended, GJPMiningco recommends removing the slide panel that covers the heatsink and adding some fans that blow down into the heatsink - at least 3 fans evenly spaced along the heatsink.Īvalon3 CGMiner Under Ubuntu 14.04 sudo apt-get update.

#BITBURNER WIKI MOD#

Guide - Dogie's Comprehensive Avalon Avalon2 Setup + Silencer Mod.

#BITBURNER WIKI MANUAL#

Reflash: sudo dd if=openwrt-brcm2708-sdcard-vfat-ext4.img of=/dev/sdb bs=4M #/dev/sdb is your memory cardĪvalon 2 units communicate with a UART, usually attached to your host via a generic USB UART adapter.įirst, figure out what COM port (or /dev/ttyUSB on Linux) and run BFGMiner with:īfgminer -S avalonmm:\\.\COM22 -set avalonmm:clock=1500 -set avalonmm:voltage=1 -set avalonmm:fan=80 Manual by others.If the Raspberry Pi can access internet, cgminer should automatic start.

You may need update the address/DNS to your local configuration.

The default firmware IP address is 192.168.0.100, you can access it by.